kunci cisco chapter 3 essentials (4.0)

A technician is installing a new power supply in a computer. Which type of power connector should be used to connect to a PATA hard drive?
Berg
mini-Molex
//Molex
20-pin ATX connector

A technician is installing a new power supply in a computer. Which type of power connector should be used to connect to a floppy drive?
//Berg
Molex
20-pin ATX connector
SATA connector


A technician is assembling a new computer. Which two components are often easier to install before mounting the motherboard in the case? (Choose two.)
//CPU
//memory
NIC
sound card
video card

Which solution should be used to clean a CPU and a heat sink?
soap and water
rubbing alcohol
a diluted ammonia solution
//isopropyl alcohol


When building a computer, which two components are normally installed in 3.5-inch drive bays? (Choose two.)
//hard drive
optical drive
//floppy drive
flash drive
video card


When installing SATA devices, how many pins are in a SATA data cable connector?
//7
34
40
80
184


A technician is troubleshooting a computer that has a malfunctioning floppy drive. The technician observes that the floppy drive light remains lit constantly. How should the technician attempt to repair the problem?
Remove the floppy drive using Add/Remove Hardware.
Replace the floppy drive.
//Connect the data cable making sure that the colored stripe on the cable is aligned with pin 1 on the drive and the motherboard.
Change the jumper setting to master for the floppy drive.




A technician has been asked to install a floppy drive that will have the drive letter B:. How can this task be accomplished by the technician?
The technician can accomplish this task by assigning the drive letter in the BIOS.
The correct drive letter can be configured using jumper settings on the drive.
The floppy drive should be connected using the second floppy drive controller.
//The floppy drive can be connected to the middle connector of a three connector floppy drive cable.



A field technician has been asked to install a wireless 802.11g NIC in a computer, but is unsure about the expansion slots available. Which two types of wireless NICs should the technician have available? (Choose two.)
//PCIe
AGP
SCSI
//PCI
SATA



Which port is typically used for external wireless NICs?
Parallel
PS/2
SCSI
//USB


Which additional 4-pin or 6-pin power connector is required by some motherboards?
//AUX
Berg
Parallel
SCSI

A technician is installing a new CPU in a ZIF socket on a motherboard. What is the primary way of securing the CPU in place?
thermal compound
antistatic fasteners
//load lever
screws

Which type of drive is installed in a 5.25-inch bay and can be accessed without opening the case?
hard drive
//optical drive
floppy drive
LS120 drive



After a technician has assembled a new computer, it is necessary to configure the BIOS. At which point must a key be pressed to start the BIOS setup program?
before the computer is powered on
during the Windows load process
//during the POST
after the POST, but before Windows starts to load

Refer to the exhibit. Which type of hard drive uses the power connector shown?
ATA
EIDE
SATA
SCSI
USB

What is the most reliable way for users to buy the correct RAM to upgrade a computer?
Buy RAM that is the same color as the memory sockets on the motherboard.
The RAM chip should be the same size than the ROM chip.
Ensure that the RAM is compatible with the peripherals installed on the motherboard.
//Check the motherboard manual or manufacturer's website.



Refer to the exhibit. Which type of port is shown?
FireWire
graphics
RJ11
RJ45
//USB



A technician has just finished assembling a new computer. When the computer is powered up for the first time, the POST discovers a problem. How does the POST indicate the error?
//It issues a number of short beeps.
The LED on the front of the computer case flashes a number of times.
It places an error message in the BIOS.
It locks the keyboard.


Which action is recommended to prevent the motherboard from contacting the metal base of the case?
Ensure that the non-conductive side of the case is beneath the motherboard.
//Use standoffs to keep the motherboard above the metal base.
Place a non-conductive barrier between the motherboard and the metal base.
Use a self-adhesive non-conductive membrane on the underside of the motherboard.